Last updated: November 2026

When the leaves come down and the dock crew starts calling, it is time to think about the gear that has been on your dock and boat all summer. Rod holders, cup holders, tables, ladders, lights and bumpers all last longer when they come off before ice season and get stored the right way. A little effort in October also means everything is clean, accounted for and ready to go back on in spring.
Quick answer: how to store dock and boat accessories for winter
- Remove accessories before the dock or boat comes out of the water.
- Photograph or note where everything was mounted.
- Clean each piece with fresh water and mild soap, then rinse.
- Let everything dry completely.
- Inspect clamps, thumb screws and hardware, and set aside anything that needs replacing.
- Bag and label small hardware with the item it belongs to.
- Store everything somewhere dry, off the floor and out of direct sun.
Why take accessories off at all?
Plenty of people leave gear mounted and hope for the best. A few reasons not to:
- Ice and freeze thaw cycles. Ice expands and shifts, and water trapped in holders and brackets freezes and thaws all winter long. That puts stress on anything still attached to a dock section, lift or rail.
- Dock removal. Dock sections get lifted, stacked and moved. Anything still clamped on can get knocked loose, bent or lost in the shuffle.
- Hardware disappears. Small parts left outside over the winter have a way of going missing by spring.
- Theft and weather. A closed up lake property is quiet for months. Gear stored inside is out of sight and out of the weather.
When should you start?
The best time is before your dock and boat come out, not after. In the Upper Midwest, many lake owners pull docks and boats from mid October into early November, and dock and lift services book up fast. Taking accessories off a few days before haul out keeps them from getting damaged when sections are moved. In warmer climates where boats stay in the water year round, a fall cleaning and inspection is still worth doing.
Step 1: Document your setup
Before you remove anything, take a few photos of the dock and boat. Note which post held the rod holder, where the cup holders sat on the rail, and which side the table was on. In April you will be glad you did, especially if a different person handles the spring install.
Step 2: Remove accessories
How easy this step is depends on how your gear was installed. Anything drilled, screwed or bolted in takes more time and may leave holes behind. Clamp style and slide on accessories come off in minutes. Here is how a few common types come off:
| Accessory type | How it usually comes off | Storage tip |
|---|---|---|
| Dock post rod and cup holders | Loosen the thumb screw or clamp and lift off the post | Keep the clamp and any spacers with the holder |
| Pontoon rail rod holders | Loosen the thumb screw bracket and slide off the rail | Store upright so rod slots keep their shape |
| Rail cup and wine glass holders | Slide off the rail or loosen the clamp, depending on the design | Pull out removable stainless inserts and clean separately |
| Post mounted boat tables | Remove according to the table's mounting system | Store the table top flat or on edge indoors |
| Ladders, bumpers and solar lights | Unbolt or unclip per the manufacturer | Charge or remove batteries from lights before storage |
Our own dock and rail accessories are designed for this kind of seasonal on and off:
- Dock Post Double Rod and Cup Holder, which uses a two position clamp with a stainless steel thumb screw, needs no tools and fits round and square posts up to 4 inches.
- Dock Post 4 Rod Holder, with the same tool free thumb screw clamp, for round or square posts up to 2.625 inches.
- Pontoon Boat Fishing 4 Rod Holder, which clamps to the rail with a thumb screw bracket and comes off without tools.
- Pontoon Rail Cup and Wine Glass Holder, which slides off the rail, with a removable stainless steel cup insert that pulls out for cleaning.
Step 3: Clean before you store
Putting gear away dirty is the most common mistake. Dried algae, fish slime, sunscreen and spilled drinks are much harder to remove in spring, and grime holds moisture against hardware all winter.
- Wash with fresh water and a mild dish soap using a soft brush or sponge.
- Skip harsh solvents and abrasive pads, which can scratch plastic surfaces and finishes.
- Rinse stainless steel parts thoroughly, especially if you boat in salt or brackish water. Salt left on stainless is one of the main causes of surface rust spots.
- Let everything dry completely before it goes into a bin or bag.
For more on why rinsing matters, see how sun and salt exposure affect marine grade hardware.
Step 4: Inspect hardware
With everything clean, it is easy to spot problems. Check thumb screws for smooth threads, look at clamps and brackets for cracks or bends, and check stainless parts for pitting. Make a list of anything that needs replacing now, while you have the whole winter to order it, instead of finding out on the first warm weekend in May.
If a stainless cup insert is dented or missing, a Replacement Stainless Steel Cup Holder is available for our holders.
Step 5: Store it the right way
- Dry and covered. A garage, shed, basement or storage room works. Avoid spots where water drips or pools.
- Off the floor. Shelving or bins keep gear away from moisture and from getting stepped on.
- Bag the small parts. Put hardware in a zip bag and tape or tie it to the item it belongs to. Label it.
- Do not stack heavy items on top. Long term weight can warp plastic parts and table tops over a winter.
- Out of direct sun. A sunny window can put more UV on gear over the winter than you might expect.
Step 6: Do not forget the rest of the dock and boat
While you are at it, run through the bigger items:
- Boat covers cleaned, dried and stored, or installed properly if the boat stays covered outside.
- Batteries removed or put on a maintainer according to the manufacturer.
- Life jackets, throw cushions and ropes washed, dried and stored indoors.
- Engine and fuel system winterized according to your owner's manual or by your marina.
- Dock sections, lifts and canopies removed or secured according to your installer.
Some gear does not have to hibernate
Not everything needs to sit in a bin until spring. A portable rod caddy or a wall mounted fishing station can go straight to the garage or ice house for winter fishing. Our cold weather and ice fishing rod holder guide covers what works best once the lake freezes.
Frequently Asked Questions
Should I take my dock accessories off for the winter?
Yes, in any area where the lake freezes. Ice movement, freeze thaw cycles and dock removal can damage or loosen anything left attached. Removing, cleaning and storing accessories indoors helps them last much longer.
Can marine grade HDPE stay outside in the winter?
Marine grade HDPE is built to resist cracking, fading and splitting, and it handles cold better than many standard plastics. Even so, removing accessories from docks and boats protects them from ice, impact and lost hardware, and keeps them clean and ready for spring.
How do I clean stainless steel cup holders before storing them?
Rinse with fresh water, wash with mild soap and a soft cloth, rinse again and dry completely. If you boat in salt water, rinse more thoroughly to remove salt residue, which can cause surface rust spots.
When should I take my dock out in Minnesota and the Upper Midwest?
Many owners remove docks and boats between mid October and early November, before the first hard freeze and ice forms. Dock and lift services fill their schedules early, so book ahead.
Should I store my boat table indoors for the winter?
Yes. Removing the table and storing the top indoors, flat or on edge with nothing heavy stacked on it, protects it from ice, snow load and UV through the off season.
How do I keep small hardware from getting lost over the winter?
Put screws, spacers and clamps in a labeled zip bag and attach it directly to the accessory it belongs to. Taking photos of your setup before removal also makes spring installation faster.
Planning upgrades for next season? Browse our Dock Accessories and Pontoon Accessories, designed and made in the USA.